Your home's exterior takes a beating every single day — sun, wind, rain, impact. When siding fails, moisture gets in fast and damage follows. Forge Siding sends licensed Siding crews across Albion, NY to inspect, repair, and replace with zero guesswork.
We didn't start Forge Siding to push volume — we built it because homeowners in Albion kept getting burned by crews who cut corners on material selection, skipped moisture barriers, and left job sites messy. That's not how we work. Every Siding project starts with an honest assessment: we look at your substrate condition, check for existing rot or moisture intrusion, and talk through your options before a single nail goes in.
Our crews are licensed, carry full general liability and workers' comp, and every lead installer has completed manufacturer certification training. We work with fiber cement, engineered wood, vinyl, and steel systems — and we'll tell you straight which one makes the most sense for your home's structure, your local weather patterns, and your budget. No upselling, no pressure.
Most homeowners don't notice siding problems until water damage has already reached the sheathing. These are the signals worth acting on before the repair scope doubles.
Hairline cracks look cosmetic but they're water channels. Once moisture gets behind the panel and hits the housewrap — or finds no housewrap at all — sheathing rot starts within one season.
Panels that bow outward have usually absorbed moisture or were installed without adequate expansion clearance. Warped vinyl or fiber cement can't seal properly at the joints, so the problem accelerates.
Paint peeling on your inside walls near exterior surfaces is a classic sign that moisture is migrating inward through failing siding. By the time you see it inside, the wall cavity is already compromised.
Panels that have pulled away from the wall are an open door for pests, moisture, and cold air. Nails back out over time when the substrate is soft — often a sign of prior water damage underneath.
Old or failing siding, particularly if the housewrap underneath has deteriorated, acts like a thermal short-circuit. Your HVAC runs harder to compensate, and the bills reflect it before the siding looks obviously bad.
Extreme fading means UV degradation — the protective surface layer is gone. Chalking on older paint-based systems signals the same. At that stage, the panel is no longer blocking UV penetration to the substrate underneath.
Every job below starts with a free written estimate. We specify the product, the profile, the color, and the installation method upfront — so there's no ambiguity when work begins.
Fiber cement comes in lap, panel, and shingle profiles, and we've installed all three on everything from Cape Cods in historic neighborhoods to large multi-unit builds. Correct installation matters enormously with this material — improper fastening or insufficient clearances void the warranty and cause edge-swell failures. Our lead installers are trained to the spec sheet, not just to what looks right on the jobsite.
Done right, vinyl siding is durable, low-maintenance, and cost-effective. Done wrong — wrong gauge, wrong fastener pattern, no expansion clearance — it warps in the heat and pulls loose in wind. We use .044" and .046" gauge panels minimum and follow thermal expansion specs precisely for NY's temperature range. Nail hem fastening at 16" centers, 1/32" expansion gap at all trim terminations, and a fully integrated vinyl accessory system so the corners, J-channel, and window trim all work together.
Engineered wood is popular in Albion neighborhoods where the traditional wood look matters architecturally but the maintenance demands of real cedar or pine aren't practical. We install with stainless or hot-dipped galvanized fasteners to prevent iron staining at the nail head — a detail that separates a professional installation from a quick flip job.
Our repair crews use the same material standards as our full-installation teams — no caulking over gaps as a permanent fix, no missing sealant at transitions, no shortcuts on housewrap at the repair perimeter. If there's rot in the sheathing behind the damaged panel, we address it during the repair rather than covering it up.
We work with metal panel systems, large-format fiber cement, and commercial-grade vinyl for multi-family and light commercial applications. EIFS compatibility work, expansion joint detailing, and coordination with waterproofing and window subcontractors are all in scope. We carry the insurance requirements for commercial GC work and can provide certified payroll documentation for public projects.
Siding that terminates at rotted or missing fascia boards isn't protected — it's channeling water straight into the rafter tails. We routinely pair siding replacement with trim, soffit, and fascia work so the entire exterior envelope is addressed in one mobilization rather than two. PVC trim board, prefinished aluminum coil, and fiber cement fascia are all in our wheelhouse.
Four steps. Each one documented. No surprises at the invoice.
We come out, examine your existing cladding, probe for soft substrate, check flashing and housewrap condition at visible penetrations, and give you an honest assessment of what we're working with. No high-pressure sales — just a clear picture of the project scope before we talk numbers.
You receive a line-by-line written estimate: material cost by product and quantity, labor, removal and disposal of existing siding, and any sheathing repair identified in the assessment. We walk through material options with physical samples, not just catalog photos. You sign off on the spec before we order anything.
Your start date is locked at signing. Crew arrives on time, materials are staged and ready, and the site is protected before demo begins. We run a tight job — no leaving panels exposed overnight when rain is in the forecast.
At project completion, we walk the entire exterior with you. Every run of siding, every corner, every trim termination — you look at it before we close out. If anything isn't right, it gets fixed on the spot. Our goal is that you refer us to your neighbor the week after the project wraps.
Every crew that works on your home carries a current contractor's license for NY, full general liability, and workers' compensation. We'll email you the certificates before we arrive — not after you ask three times.
Upfront pricing means you know what you're paying before a single panel comes off the wall. Change orders require your written approval. We've built our reputation in Albion, NY on the fact that our estimates are reliable.
When we book your project, we commit to a start date. No bumping you for a bigger job, no weeks of silence after signing. We operate with enough crew capacity to honor the schedule we gave you.
We've seen what happens when crews leave siding debris sitting for a week. Nails in the lawn, panels blocking access, dust in the HVAC intake. Our cleanup protocol runs end-of-day, not end-of-project.
Our workmanship warranty covers what we did and how we did it. The product carries the manufacturer's own warranty on top of ours. That means your home is protected twice — by the material the manufacturer stands behind, and by the installation Forge Siding guarantees.
Talk to Us About Your Project — +1-844-782-0929Straight from the homeowners we've worked with across Albion and Albion, NY.
We were replacing deteriorated T1-11 on a house we'd bought the year before. Forge Siding walked us through why HardiePlank made more sense than vinyl for our wall orientation and explained the flashing work that needed to happen around the windows before panels went on. Project started on the date they said. Crew cleaned up every afternoon. The job came in within a couple hundred dollars of the estimate.
I manage a twelve-unit building in Albion and we needed LP SmartSide on three facades before winter. Forge Siding coordinated with our property manager, worked around tenant schedules, delivered materials in two staged drops to keep the lot clear, and finished four days ahead of the original schedule. Commercial billing was clean and documented. They're on our preferred vendor list now.
We went with insulated vinyl — Forge Siding recommended the insulated backer for our exposure and the energy savings have been real. First heating season after the install, our gas bill dropped noticeably. Installation crew was professional, on time every day, and the lead installer walked me through every elevation before he called the project done.
I had a specific architectural profile I wanted for the gable ends — a shingle exposure pattern — and everyone else told me it was a custom order with a six-week wait. Forge Siding had it in stock through their regional supplier and we started within two weeks of signing. The detail work at the gable peaks is clean and exact. Not every contractor has the skill to do that level of trim work.
I'm a home inspector by trade, so I know what cutting corners on a siding installation actually looks like behind the panels. Forge Siding's work is correct — right fastener pattern, proper clearances from grade and roofline, continuous housewrap with taped seams at all penetrations. This is how it's supposed to be done and most of the crews I see in Albion, NY don't do it this way.
We had three bids and Forge Siding was the only contractor who physically checked the housewrap condition before quoting. Everyone else just looked at the surface. They found a section of torn WRB behind the garage bay that needed patching and included it in the estimate. When you're spending this much on an exterior, you want a company that checks the whole wall system, not just what they can see from the ground.
Real questions, real answers — no filler.
We're not a national call center subcontracting your project to whoever's available. Our crews are based in and around Albion, NY. We know local code requirements, local supplier lead times, and local weather patterns — and that local knowledge shows up in how the project runs.
Our primary service area covers Albion and surrounding communities within our regional radius. Call +1-844-782-0929 to confirm service availability at your address — we'll tell you same-day.
Don't let failing siding go another season. Call Forge Siding and we'll have an estimator out to your property within 24 hours.
Call +1-844-782-0929 Now